Skip to content
CramShare
FreePractice exam

The electrical nccer test questions and 100 correct answers new 2026

ENGI100 Engineering — exam and revision material · Other

Updated today

Engineering exam material, 19 pages. Originally published on StudyMerit.

Pages
19
Academic year
2025/2026
Language
English

What’s included

Preview 3 of 19 pages

See the first 3 pages exactly as they appear in the document.

Read page 1 as text

Which Article of the NEC covers grounding? - ANSWER article 250 Which of the following is a 90 degree, explosion proof fitting? - ANSWER GUAL What is a dropout plate? - ANSWER Metal plate with a curved surface for cable to follow as it passes from the tray All of the following are common service voltages in the United States EXCEPT: - ANSWER 372/575 3 - PHASE, 4 - WIRE What does a GFCI breaker do? - ANSWER Opens a circuit to prevent operation of an electrical device What will happen when one or more coils in a winding are grounded? - ANSWER The motor will automatically blow fuses Eight incandescent lighting fixtures are to be installed. Each fixture is 120 - volts, with a 200 - watt lamp. What is the total connected load? - ANSWER 13.3 amps The must be grounded in a bussed gutter if used as the main service equipment. - ANSWER Neutral busbar When wall mounting cable tray, ensure that - ANSWER The building structure is strong enough to support the tray system The purpose of sealing cable ends when reels of cable are in storage is - ANSWER To keep moisture from creeping in The outer covering on liguid - tight flexible metal conduit is used for - ANSWER A moisture seal A good electrical connection should - ANSWER Be mechanically and electrically secure The symbol normally used for duplex - ANSWER Circle with two parallel lines drawb through it Disconnecting means are covered in - ANSWER NEC Section 110 - 22 In relation to switches, the term throw refers to the - ANSWER Number of internal operations that a switch can perform

Read page 2 as text

A 3 - phase, 4 - wire, 480v service requires ______ current transformer(s) - ANSWER 3 Services conductors and equipment are covered in - ANSWER NEC Article 230 The NEC required that all receptacles installed on 25 amp and 20 amp branch circuits be ______ receptacles - ANSWER Grounding A transformer with the primary of 400 turns and a secondary of 300 turns has a _____ - ANSWER Step - down turns ratio of 4:3 The circular mil is based on the - ANSWER Cross - sectional area of the wire Of the termination classes listed below, ____ is the only one that provides a seal against external elements. - ANSWER Class 1 Unless otherwise noted. the calculations in AC circuits _____ values. - ANSWER Rms When the coil turns are increased the _____ - ANSWER Induced voltage is increased As the temperature surrounding a self - regulating heating cable rises, the ____ - ANSWER Resistance of the polymeric core increases The motor type that has the highest starting torque is the ____ motor. - ANSWER Capacitor - start For a given number of poles, the ____ determines the speed of an AC motor. - ANSWER Frequency Both induction and synchronous motors operate on the principle of a rotating ____ field - ANSWER Magnetic A transformer has 200 turns in the primary, 150 turns in the secondary, and 120VAC applied to the primary. The voltage across the secondary is: - ANSWER 90Volts The output capacity of a motor is rated in - ANSWER Horsepower The synchronous speed at which a pole, 60 Hz induction motor operates is rpm. - ANSWER 1,800 The sine of 0 degree is - ANSWER 0

Read page 3 as text

Meters used in AC circuits indicate the - ANSWER Effective The component labeled 7 in figure 1 is a(n) - ANSWER End seal In an AC circuit containing resistance only _____ will flow if the resistance is 10 ohms and the voltage is 120V. - ANSWER 12A The _____ rotor types are generally rugged. - ANSWER Squirrel cage Proofs tests are made at_ of the original factory voltage. - ANSWER 60% Which type of heating cable cannot be cut and terminated in the field? - ANSWER Mineral insulated The secondary of a CT under load should not be opened because of_. - ANSWER Induced high voltage In a transformer ______ - ANSWER Electromagnetic Induction Ocurs When a ground rod is installed, the top of the rod must be positioned ______ grade. - ANSWER Flush with or below When making offset bends, the two kicks must be made perfectly parallel or the resulting offset will have a _____ - ANSWER Crooked Bend conduit that requires a 90 degree change in direction, except 42.All of the following types of condulet may be used as a pulling point for _____ - ANSWER C To be effective, a grounding system must limit the voltage on the electrical system and protect it from all of the following, except _____ - ANSWER Undervoltage conditions What is the MOST common service used in a temporary power panel? - ANSWER 120/240 volt, 1 - phase, 3 - wire What are the 2 MOST common types of overcurrent protective devices? - ANSWER Circuit breakers and fuses What instrument is used to perform an insulation - resistance test on a 480 - volt motor winding? - ANSWER Megohmmeter Why is a seal installed in a run of conduit in a Class I location? - ANSWER Prevent the passage of explosive gases in the conduit Which of the following is the correct formula for OHM's law? - ANSWER I=E/R

That’s the free preview

You’ve read 3 of 19 pages. The whole document is yours with a free account, and it stays in your library.

Free

With a free account